WEEK 14 (FYP2) - INDUSTRIAL DAY

Objective: 

1) To present the project that develop

2) To demo the project

Analysis/Discussion:

During week 14, basically the presentation day to the project  that develop at assessors to give mark and give the feedback about this project. The assessors that decided for this project are Madam Siti Zaiummi binti Mohd Zawawi and Madam Salmi binti Idin. Firstly, I present my project to assessors based on my poster. My project are totally showed from introduction until conclusion at the poster. So, I only explain more details about my project with full confident and  make the assessors understand about my project. After finished the explanation about my project, the assessors ask me some question regarding my poster. I answering the question smoothly until they satisfied with my answer. Lastly, I bring the assessors to outside the hall because I want to demo my project to them. The demo is to prove my project whether function or not and my project totally function. The feedback from assessors are positive after the demo.

During presentation to the assessors

After finished the presentation

Conclusion:

Finally, the Industrial Day/ Presentation Day was successfully done without has any problem. The system of my project working properly and the project successful to finished. So, for the next step is to submit my final year project full report with hardcover to my supervisor and university library.

WEEK 13 (FYP2) - MAKING THE PREPARATION FOR THE INDUSTRIAL DAY AND DESIGN POSTER

Objective:

1) To repair the draft for final project report  

2) To design the poster for industrial day. 

Analysis/Discussion:

During week 13, basically repair  the final report draft for this project after referred from supervisor. Then, design the poster for presentation day about the project develop. After that, make the final preparation for presentation day by test the hardware prototype and select the specific information to put in the poster.

This week the draft report was repair and finish write then, the poster was design successfully by add the important information about this project and was printed A1 size ready to present next week during presentation day. All preparation was successful and do not has any problem to prepare because by follow the gantt chart that guide the successful of this project so the work was finish during the due date without has any problem.

Figure 1: Poster Development of Bike Security System

Conclusion:

   Finally, the draft final report that write followed the correct guideline and was repair by add some suggestion from supervisor madam noor hidayah. Then, poster design was finish  and ready for presentation day next week.

WEEK 12 (FYP2) - TOUCH UP THE FINAL REPORT DRAFT 

Objective:

1) To touch up the final report draft.

Analysis/Discussion:

During week 12, basically write the draft report. The draft report was cover from chapter 4 and chapter 5 only because chapter 1, chapter 2 and chapter 3 was completed in final year project 1 last semester. By refer the proposal report was finish from Final Years project 1 and the result that record for this project all information was collect and put into the draft report. The draft report making more easy and do not has any problem by follow the guideline how to write the final report.

Conclusion:

After complete the draft report for chapter 4 and chapter 5, the draft report was sent to madam noor hidayah binti mohd yunus to checking either it correct or not.

WEEK 11 (FYP2) - FINAL YEAR PROJECT BRIEFING #2 AND TROUBLESHOOT THE PROJECT.

Objective:

1) To attend final year project briefing #2.

2) To troubleshoot the project.

Analysis/Discussion:

Basically on week 11, has briefing #2 for final year project. During final year project briefing inform the guideline during the industrial day and also the guideline how to making the poster for the project develop. Then, the lecturer remind to get ready for the industrial day.

Figure 1: The memo for final year project briefing

Besides that, the process of combining the hardware prototype to the bike is continued. The problem of previous work is solved by using troubleshooting method with the guide of some friends.   

Conclusion:

Finally, the objectives of development of bike security system are achieved where to make the bike will not easily to START, to get the people surrounding alert when the bike try to be stolen and to designed and develop the hardware security system of the proposed system. 

WEEK 10 (FYP2)- WIRING THE HARDWARE PROTOTYPE TO THE BIKE

Objective:

1) To wiring the hardware prototype to the bike.

Analysis/Discussion:

During week 10 basically after doing some research about bike wiring, I'm doing the wiring connection between my hardware prototype into my bike. After that, test and troubleshoot the wiring connection if function or not.While during the wiring connection, there were some problem occurred such as integrated circuit (IC) PIC 16F877A burned and the bike still can be function even though the key in password is wrong.  

Figure 1

Figure 2

Figure 3

Conclusion:

The process of combining hardware prototype to the bike is not easy as I thought where some problem occurred during the process. The process continued until week 11.

WEEK 9(FYP2)- STUDY ABOUT BIKE WIRING.

Objective:

1) To study about bike wiring diagram.

Analysis/Discussion:

Figure 1: Bike wiring diagram.(Reference 1)

Figure 2: Bike wiring diagram.(Reference2)

Figure 3: Bike wiring diagram.(Reference 3)

For this week, The output of my project is bike. So I must study about bike wiring connection. I can choose to use dc motor replace the bike as a output for this project. But I think I want to try challenge myself to connect my project into the bike. Many resources to refer the wiring connection of bike at the internet. Figure above as an example of bike wiring connection. Besides that, I also refer or ask my friends to give their opinion about bike wiring system to me.  

Conclusion:

Finally after research about bike wiring system, I more confident to connect my circuit into the bike because wiring system of the bike are not difficult as we are expected.

WEEK 8(FYP2)- FINAL YEAR PROJECT  2 BRIEFING FOR 1ST TIME

Objective:

1) To attend Final Year Project 2 briefing.
2) To build the new hardware prototype for this project.

Analysis/Discussion:

    During week 8 basically has attend the Final Year Project 2 briefing then continue by doing the new hardware prototype for this project. I only to buy a prospect item at signboard shop for the new hardware prototype for this project. The other items such as cordless drill, glue gun, and others have already. So, the new hardware prototype for this project can be build by measure the dimension of the complete circuit at first step. Then, to cut the prospect according to the size of the measured to build the new hardware prototype.The dimension that use to build the new hardware prototype for this project about the 20 cm wide x 24 cm length x 11 cm height.  After that, glue all prospect that cut become a rectangular box by using the glue gun. Then, the complete circuit will be located at the base surface of the box while only keypad, led and lcd are located at the upper surface of the box to display them.

Figure 1 : The hardware prototype for this project

 Conclusion:

         Finally,the new hardware prototype for this project was built. The new hardware prototype look very nicely, small and so compact compare with the old hardware prototype. So, the hardware prototype can be connected to the motorcycle after this.